상품상세정보
 |
 |
 |
 |
 |
 |
Description
Brings the magic of reamping to the masses.
The Radial X-Amp 500 Reamp is one of the eight modules
designed to be comprise the Radial Workhorse Rack and Mixer System that combines
the popular 500 series platform with an incredibly flexible patching system to
let you create the ultimate studio environment.
The Radial X-Amp is a
500 series module that lets you take a pre-recorded guitar track and send it
back to amplifiers and effects so that you can tailor the sound to suit. The
advantages of Reamping are many: when recording, the guitarist need only
concentrate on the performance. Working out specific sounds and optimal mic
placement can be done later. This eliminates hours of tiresome repetition while
allowing the producer to adjust the character of the track as the production
evolves.Using the X-Amp is 'plug and play' easy to use. The design begins with
an XLR balanced line level input located on the 500 series rear panel that feeds
the X-Amp. To ensure the very highest fidelity, 100% discrete class-A circuitry
is employed. The X-Amp unbalances and buffers the pre-recorded signal where it
then feeds two transformer isolated hi-Z guitar level outputs. The ¼" jacks are
front mounted for desk-top convenience and equipped with ground lifts to help
eliminate hum and buzz caused by ground loops. Independent level controls enable
you to adjust the drive going to each amp for optimal tone. Should one of the
amps be out of phase, depressing the 180° quickly brings both in line. The X-Amp
Reamper works with guitars, basses, keyboards and even voice! You can send the
signal through guitar effects pedals too. In fact the only thing holding you
back is your imagination.
Features
- Active Reamp designed for 500 series racks
- 100% discrete class-A electronics for best tone
- Transformer isolated to eliminate hum and buzz
- Easy access front panel jacks & controls
Specifications
X-Amp 500 Reamp Specifications:
- Circuit type: Class-A discrete, transformer coupled
- Power Requirement: 40mA, +/-16VDC
- Frequency Response: 20Hz to 20kHz (adjusted for guitar signals -5dB@20kHz) - 100K Load
- XLR
- Voltage Gain:
- XLR Input to XLR Output: 0dB +/- 0.5dB
- Omniport to XLR Output: -3dB +/- 0.5dB
- XLR Input to 1/4” outputs: -0.6dB +/- 0.5dB
- THD+N:
- XLR Input to XLR Output: <0.002% @ 0dBu(20Hz~20kHz)
- Omniport to XLR Output: <0.002% @ 0dBu (20Hz~20kHz)
- XLR Input to 1/4” outputs: <0.006% @ 0dBu (1KHz)
- Noise:
- XLR Input to XLR Output: -114dB below 0dBu
- Omniport to XLR Output: -95dB below 0dBu
- XLR Input to 1/4” outputs: -98dB below 0dBu
- Intermodulation distortion:
- XLR Input to XLR Output: <0.04% @ 0dBu input
- Omniport to XLR Output: <0.005% @ 0dBu input
- XLR Input to 1/4” outputs: <0.027% @ 0dBu input
- Maximum input:
- XLR Input to XLR Output: +26dBu
- Omniport to XLR Output: +20dBu
- XLR Input to 1/4” outputs: +19dBu
- Connector I/O details
- XLR input type**: +4dB, balanced female XLR, AES standard, input impedance 1.2k Ohms
- XLR output type**: Parallel ‘thru-put’ with XLR input, +4dB balanced, output impedance 600 Ohms
- ** Typical connectors found on most 500 series racks
- OUT-1 type: Instrument-level (variable), unbalanced 1/4”, transformer isolated, impedance 3k Ohms
- OUT-2 type: Instrument-level (variable), unbalanced 1/4”, transformer isolated, impedance 3k Ohms
- Omniport type: Instrument-level input, unbalanced 1/4”, (on Workhorse), input impedance 220K Ohms
- Shipping Weight: 1.5lbs (0.7kg)
- Size: Standard 500 series rack format
- Warranty: 3 years, transferable
관련 상품
배송안내
|
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
교환 및 반품안내
|
||||||||||||||||||||||||||||||||||||
이미지 확대보기X-Amp 500
비밀번호 인증
글 작성시 설정한 비밀번호를 입력해 주세요.
장바구니 담기
상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?
찜 리스트 담기
상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?
평일 오전 9:00 ~ 오후 6:50
토요일 오전 9:00 ~ 오후 3:00
은행 : 국민은행
예금주 : 이정석
