DN530 Architect's & Engineers Specification

The Noise Gate shall provide four (4) complete channels of creative transient-accentuating gating in a standard 1U 19" rack mount chassis. Each channel shall have an electronically-balanced input and output on 3-pin XLR connectors.

Each channel shall have a rotary Threshold control to set the signal level at which the Noise Gate opens. The channel metering shall have a green "THR" LED to indicate when the signal exceeds this threshold.

Each channel shall have rotary controls for setting the Attack, Hold and Release times of the Noise Gate. The channel metering shall have a yellow "HLD" LED to indicate when the Hold portion of the dynamic control envelope is active and an orange "REL" LED to indicate when the release portion of the dynamic control envelope is active. The Hold function shall also have Intelligent Threshold Shift (i-TS) to provide threshold hysteresis to avoid repeated opening and closing of the Noise Gate in response to low frequency signals close to the threshold level set by the user.

Each channel shall have an Accent rotary control to accentuate the initial transient that opens the Noise Gate by adding an overshoot characteristic with up to +12 dB of gain as the Noise Gate opens. The channel metering shall have a blue "ACC" LED to indicate when the Accent function is adding gain to the initial transient. The Accent shall also function independently of the noise gate when the range control is set to 0dB.

Each channel shall have a latching pushbutton switch with an associated orange LED labelled "DUCK" to reverses the operation of the gate so that it closes when signals exceed the threshold set by the user and opens when they go fall below the set threshold. When the Duck function is active, the Accent rotary control and "ACC" LED shall be disabled.

Each channel shall have a rotary Range control to adjust the amount of gain reduction applied to signals below the threshold level. Each channel shall also have a red "SHUT" LED to indicate when the Noise Gate is fully closed.

Each channel shall have a latching pushbutton switch with an associated red LED labelled "BYPASS" to remove the Noise Gate from the signal path.

Each channel shall have a Clip LED included in the channel metering to indicate when the input signal is exceeding the clipping point of the Noise Gate.

Each channel shall also have a sidechain control section with a bandpass filter controlled with a rotary control labelled Frequency to set the filter centre frequency. The sidechain control section shall have a latching pushbutton switch with an associated green LED labelled "FILTER" to put the bandpass filter in the sidechain signal path. The sidechain control section shall also have a latching pushbutton switch with an associated yellow LED labelled "EXT" to select the external sidechain ¼" TRS Jack input as the signal source for the sidechain instead of the signal that the Noise Gate is acting on.

The Noise Gate shall have a Solo Bus to allow monitoring of the sidechain control input signals for each channels. The Solo Bus shall have input and output XLR connectors on the rear panel to facilitate the serial connection of units and to connect to a line input on a mixing console for monitoring via its Solo Bus console headphone amp.

The sidechain control section of each channel shall have a latching pushbutton switch with an associated yellow LED labelled Solo to enable the post-filter sidechain signal onto the Noise Gate solo bus.

The Noise Gate shall meet or exceed the following specifications:

Distortion: 0.05% (1kHz 0dBu)
Dynamic range: 116dB (20Hz-20kHz unweighted)
Frequency response: ±0.5dB (20Hz-20kHz, relative to 1kHz)
Noise floor: -100dBu gate closed (20Hz-20kHz unweighted)
-94dBu gate open (20Hz-20kHz unweighted) 
Attack time: 30us-10ms
Hold/Release time: 2ms-2 secs
Maximum output level: +22dBu into 600 ohms

The Noise Gate shall have an integral switch-mode power supply capable of operating from a 100 - 240 V a.c. ±10%, 50 to 60 Hz AC power source and have an IEC 60320 C14 mains inlet with integral fuse. A blue LED labelled "POWER" shall be included on the front panel to indicate when the unit is powered on.

The Noise Gate shall be the KLARK TEKNIK Model DN530 and no alternative specification option is available.

DN530 Technical Specifications

Inputs - Four
Type: Analogue, electronically balanced female XLRs (Pin 2 hot)
Impedance: 10kΩ
Maximum input level: +22dBu
Common mode rejection: Typically, -80dB at 1kHz

Outputs - Four
Type: Analogue, electronically balanced male XLRs (Pin 2 hot)
Output impedance: <60Ω
Maximum output level: +22dBu
Signal drive capability: <600Ω

EXT SIDECHAIN inputs - Four
Type: Analogue, electronically balanced Jack sockets
Impedance: 20k
Maximum input level: +22dBu
Common mode rejection: Typically -60dB at 1kHz

SOLO BUS input - One
Type: Analogue, electronically balanced female XLR (pin 2 hot)
Input impedance: 20kΩ
Maximum input level: +22dBu
Common mode rejection: Typically -60dB at 1kHz

SOLO BUS output - One
Type: Analogue, electronically balanced male XLR (pin 2 hot)
Output impedance: <60Ω
Maximum output level: +22dBu
Signal drive capability: <600Ω

Performance
Maximum gate gain reduction: Greater than -90dB
Maximum accent gain: +12dB
Maximum signal level any input or output: +22dBu
Noise at main output with unity gain: -94dBu
Distortion at 1KHz 0dBu with steady unity gain condition: <0.05%
Signal delay: 0 seconds
Frequency response: ±0.5dBu (input to output), 20Hz to 20kHz
Dynamic range: >116dB (22Hz to 22kHz unweighted)

Gate
Threshold: Scale = -50dB to +25dB
Range: Scale = -4 (minus infinity) to 0dB
Attack: Scale = 30µs to 10ms
Release: Scale = 2ms to 2s
Hold: Scale = 2ms to 2s
Accent: Scale = 0dB to +12dB

Filter
Sidechain filter: Scale = 40Hz to 16kHz

Terminations
Audio: 3-pin XLRs (male and female) and 1/4" TRS balanced jack sockets
Power: 3-pin IEC

Power requirements
Voltage: 100VAC to 240VAC ±10%
Frequency: 50Hz to 60Hz
Consumption: <25W

Dimensions
Height: 44.5 mm (1.75"), 1U high
Width: 483 mm (19")
Depth: 305 mm (12")

Weight
Net: 4.6 kg
Shipping: 5.6 kg

Operation
Temperature: +5°C to +40°C

Storage
Temperature: -20°C to +60°C

Due to a policy of continual improvement, KLARK TEKNIK reserves the right to alter the function or specification at any time without notice.